| < Sitemap < Imprint < GTCT | |||||||||||||||
 |
|||||||||||||||
| COMPANY |
 PRODUCTS |
APPLICATIONS | DOCUMENTATIONS / DOWNLOADS | TRADE SHOW CALENDAR | |||||||||||
| SENSORS | MOTION | SYSTEMS | CONTROLS | ||||||||||||
Displacement Measurement
|
|
| TECHNICAL | |
| SOFTWARE | |
| FIELDBUS FILES | |
| OPERATING MANUAL | |
| PIN ASSIGNMENT | |
| DATA SHEETS | |
| DRAWINGS | |
| PRODUCT CHANGES | |
| GENERAL | |
| BROCHURES | |
| CERTIFICATES | |
|
|
|
|
Operating manual |
Program |
||
|
deutsch
|
english
|
|||
| TRWinProg is a Windows PC program for programming of TR devices. This means that all TR product lines such as rotary encoders, linear encoders, laser measuring devices, transformation measuring systems, displays etc. can be programmed with one software. TRWinProg compatible devices are marked with the label on the left. System requirements: - 80-486 platform or higher |
|
|
COMPLETE VERSION -
contains program, help files, operating manuals and pin assignments : TRWinProg up to Windows XP |
|
|
LIGHT VERSION (Revision: 14.04.2008, version V3.59, ca. 7 MB)
contains only program: |
||||
|
TR files (< 500 kB)
for building up the parameter mask in TRWinProg. Already installed versions can be updated with these files, copying them by hand into the folder ...\Programme\TRWinProg\Devices: |
||||
|
EPROG W32 is a PC program for serial programming of position measuring devices under Windows operating systems:
- Windows 95®/98®/ME® Data interchange between the PC and the measuring device is carried out via one of the serial V.24 interfaces with 115 kbps. It is necessary to plug on the PC adapter for electrical isolation and conversion of the signal to RS485 which extends the range to max. 800 m. |
|
|
|
|
EPROG is a PC program for serial programming of position measuring devices. An IBM-compatible PC is required. The processor must be at least a 10 MHz 8088 processor or a 6 MHz 8086 processor and the operating system must be at least MS-DOS 3.0. The program also runs in the DOS box of Windows 3.1 or higher versions, then however at least a 486DX2/66 processor must be used. Data interchange between the PC and the measuring device is carried out via one of the serial V.24 interfaces with 115 kbps. It is necessary to plug on the PC adapter for electrical isolation and conversion of the signal to RS485 which extends the range to max. 800 m. |
|
|
|
|
PC100 is a PC program for serial programming of position measuring devices under MS-DOS operating systems, version 3.1. or higher up to Windows® 98.
Data interchange between the PC and the measuring device is carried out via one of the serial V.24 interfaces with 115 kbps. It is necessary to plug on the PC adapter for electrical isolation and conversion of the signal to RS485 which extends the range to max. 800 m. |
|
|
|
PCPNT |
PCPNT is a PC program for serial programming of PNT-compatible devices under MS-DOS operating systems, version 3.1. or higher up to Windows® 98. Data interchange between the PC and the measuring device is carried out via one of the serial V.24 interfaces with 115 kbps. It is necessary to plug on the PC adapter for electrical isolation and conversion of the signal to RS485 which extends the range to max. 800 m. |
|
-
|
|
LLB Utility |
LLB Utility is a PC program for serial programming of LLB-30 and LLB-60 laser measuring devices under Windows® operating systems. Supported are the COM ports 1-9. The configuration of the device can be made in a simple manner, without knowing the individual ASCII based commands. But it can be used also any other terminal program. |
LLB Utility
.net Framework 1.1 required. So please follow the link to download the program for free from Microsoft: |
||
TR_iParameter |
Software to calculate the check sum of the iParameters (F_iPar_CRC). |
-
|
-
|
|
|
LT-Prog is a Windows PC program for programming of transformation measuring systems.
Data interchange between the PC and the measuring device is carried out via one of the serial V.24 interfaces with 115 kbps. It is necessary to plug on the PC adapter for electrical isolation and conversion of the signal to RS485 which extends the range to max. 800 m. System requirements: - 80-486 platform or higher |
-
|
-
|
|
|
BE-90 Configuration Tool is a Windows PC program for programming of barcode positioning systems:
BE-90 SSI, synchronous serial interface |
|
|
|
Software and Support DVD |
The DVD contains programming software and fieldbus files for angular and displacement measurement devices as well as for application modules and driver files. |
< Order DVD (Art.nr. 490-01001)
|
||
TR-Electronic GmbH + Eglishalde 6 + 78647 Trossingen + Tel.: +49 (0)7425 / 228 - 0 + Fax: +49 (0)7425 / 228 - 33 + E-Mail: info@tr-electronic.de + Homepage: www.tr-electronic.de